HP 67XL Troubleshooting Guide

HP 67XL Cartridge Not Recognized? Fix Cartridge Problem Errors

If your HP ENVY or DeskJet says “Cartridge Not Recognized,” “Incompatible Cartridge,” “Cartridge Problem,” “Used Cartridge,” or “Non-HP Cartridge,” do not immediately order another set. First identify whether the issue is cartridge fit, protective tape, contact communication, installation, HP+, Instant Ink, region, or a damaged cartridge.

Quick Answer

Start by confirming that the printer uses HP 67 or HP 67XL, then check HP+ and Instant Ink status. Remove all protective tape, install black and tri-color in the correct slots, reseat the affected cartridge, clean only the copper contacts with a dry lint-free cloth, and perform a 60-second power reset. On supported two-cartridge HP printers, testing one cartridge at a time can help identify whether black or tri-color is causing the error.

What Does Your HP 67XL Error Message Mean?

Different messages point to different causes. Use the exact wording on the printer or HP Smart app instead of treating every warning as the same “chip problem.”

Printer Message What It Usually Means Best First Action Can You Continue?
Cartridge Not Recognized / Not Communicating The printer cannot read the cartridge correctly because of installation, contact, chip, tape, or account-related issues. Reseat, inspect tape, clean dry contacts, and reset. Troubleshoot
Cartridge Problem / Missing or Damaged The cartridge is not connected correctly, is physically damaged, or has failed communication. Remove and inspect the affected cartridge; reinstall once. Troubleshoot
Incompatible / Incorrect Cartridge The cartridge family, region, printer model, or slot may be wrong. Check the old cartridge label and full printer model. Stop & Check Fit
Used / Previously Used / Non-Original The printer has identified a remanufactured or non-OEM supply. This can be informational rather than a failure. Read the entire prompt and use OK or Continue if offered. Often Informational
HP+ Requires Original HP Cartridges The printer was activated with HP+ and is subject to HP+ cartridge requirements. Use the supply type permitted by the HP+ program. Account Restriction
Instant Ink / Subscription Cartridge Error The printer or installed supply is still connected to Instant Ink account rules. Check enrollment, billing cycle, cancellation, and cartridge type. Check Account
Low / Empty Ink After Installation Ink-status communication has not updated, the cartridge is depleted, or the printer is reading prior supply data. Check whether printing is blocked or only the level display is affected. Check Output
Blank, Streaky, or Faded Pages This is usually a print-quality or nozzle issue rather than a cartridge-recognition error. Check nozzle tape; run one alignment or cleaning cycle. Quality Fix

How to Fix an HP 67XL Cartridge Not Recognized Error

Follow these steps in order. Test the printer after each step so you do not perform unnecessary cleaning or repeatedly remove both cartridges.

  1. Confirm the exact printer model and cartridge family. Open the cartridge door and read the old cartridge label. The printer should use HP 67 or HP 67XL. Common HP 67XL references are 3YM57AN black and 3YM58AN tri-color.
  2. Check HP+ and Instant Ink before touching the cartridge. Open HP Smart or the HP account and look for HP+, Instant Ink, subscription, billing, cancellation, or account messages. A cartridge cannot override an account restriction.
  3. Remove all required protective material. Take out only the affected cartridge. Confirm that the nozzle tape, shipping cap, clip, or other packaging identified in the instructions has been removed completely.
  4. Verify the correct slot and orientation. Install black in the black slot and tri-color in the color slot. Keep the label readable and press the cartridge until it clicks securely.
  5. Inspect the cartridge for damage or ink leakage. Do not reinstall a cartridge with a cracked shell, bent contact area, loose component, or visible leak. Photograph the issue and contact the seller.
  6. Clean the copper contacts with a dry lint-free cloth. Remove the affected cartridge and gently wipe only the copper contact area. Do not touch the ink nozzles, use alcohol, add water, scrape the chip, or clean inside the printer slot.
  7. Perform a 60-second power reset. Turn the printer off, disconnect the power cord, wait 60 seconds, reconnect it directly to a wall outlet, turn the printer on, and allow it to become idle.
  8. Test the black and tri-color cartridges separately. On supported two-cartridge printers, remove the cartridge named in the error and acknowledge Single-Cartridge Mode. Then test the other cartridge. This helps identify whether black, tri-color, or the printer/account is causing the error.
Why the order matters: If the message is caused by HP+, Instant Ink, the wrong ink family, or regionalization, cleaning the cartridge repeatedly will not solve it. Check eligibility and fit first.
Stop troubleshooting and contact support if the cartridge leaks, the contact area is damaged, the shell is cracked, or the printer becomes contaminated with ink. Do not keep reinstalling a physically damaged cartridge.

How to Identify Whether Black or Tri-Color Is Causing the Error

HP 67-series printers normally use two cartridges: one black and one tri-color. Many printers in this two-cartridge family can temporarily operate in Single-Cartridge Mode.

Test With Black Only

  • Remove the tri-color cartridge.
  • Close the access door.
  • Acknowledge Single-Cartridge Mode if prompted.
  • Print a simple black-text test page.

If the printer works with black only, the tri-color cartridge or its communication path is more likely to be the issue.

Test With Tri-Color Only

  • Remove the black cartridge.
  • Install the tri-color cartridge securely.
  • Acknowledge Single-Cartridge Mode if prompted.
  • Print a color test page.

If the printer works with tri-color only, the black cartridge or its communication path is more likely to be the issue.

Temporary use only: With black only, printing is grayscale. With tri-color only, colors can print but black may appear lighter. Reinstall two working cartridges for normal output.

HP+ and Instant Ink Can Look Like a Cartridge Failure

HP+ and Instant Ink are account and service conditions, not simply cartridge models. The cartridge can physically fit while the printer still rejects it because of program rules.

HP+ Printer

HP states that HP+ printers require Original HP cartridges. If the printer was activated with HP+, a remanufactured HP 67XL cartridge may be rejected even when the cartridge number matches.

Do not keep cleaning the cartridge. Confirm HP+ status and use a supply type allowed by the program.

HP Instant Ink

Instant Ink cartridges work through an enrolled printer and account. After cancellation, HP instructs users to remove subscription cartridges and install regular cartridges when the billing cycle ends.

Confirm whether the currently installed cartridge is an Instant Ink supply or a regular retail/remanufactured cartridge.

Key distinction: An HP+ restriction, an active Instant Ink account, a wrong cartridge family, and a failed cartridge are four different problems. The correct solution depends on the exact message.

Why a New HP 67XL Cartridge May Still Be Rejected

  • The printer uses a different cartridge family, such as HP 63 or HP 64.
  • The cartridge was purchased for another country or region.
  • Protective tape or a shipping clip remains on the cartridge.
  • Black and tri-color are installed in the wrong slots.
  • The cartridge is not pressed in firmly enough to connect.
  • The copper contacts are dusty, oily, or contaminated.
  • The cartridge shell, contacts, or internal component is damaged.
  • The printer is activated with HP+.
  • The printer or cartridge is still managed by Instant Ink.
  • Firmware or dynamic-security behavior has changed recognition.

A “new” cartridge is not automatically a “correct and eligible” cartridge. Check the printer, cartridge, region, account, and physical installation as separate variables.

When Should You Replace the Cartridge or Contact Support?

Contact Support First

  • The cartridge worked before and suddenly stopped being recognized.
  • Only one color fails the single-cartridge test.
  • The exact model and HP 67/67XL family are confirmed.
  • HP+ and Instant Ink are not restricting the printer.
  • Reseating, dry-contact cleaning, and one reset did not help.

Replace Immediately

  • The cartridge leaks or has a cracked shell.
  • The copper contacts are bent, missing, or badly damaged.
  • The printer consistently identifies that cartridge as damaged.
  • The cartridge is confirmed empty or depleted.
  • The wrong cartridge family or region was purchased.
For Faster myCartridge Support

Send your order number, complete printer model, affected cartridge color, exact error message, a photo of the cartridge label, and a screenshot of the printer or HP Smart message. These details help us determine whether the problem is fit, installation, account status, chip communication, or a cartridge defect.

Need a Replacement HP 67XL Black and Tri-Color Set?

Purchase only after confirming that the printer uses HP 67 or HP 67XL and is not restricted by HP+ or an unresolved Instant Ink account.

25% OFF myCartridge remanufactured HP 67XL black and tri-color ink cartridge 2-pack with smart chips

myCartridge Remanufactured HP 67XL Ink 2-Pack

Black + Tri-color · Smart Chips Installed · For Compatible HP ENVY and DeskJet Printers

$36.00 $48.00 25% OFF price
  • Black listed yield: up to 700 pages
  • Tri-color listed yield: up to 450 pages
  • Smart chips installed; no old-chip transfer required
  • Pre-shipment recognition and leak checks
  • Lifetime warranty and 30-day returns
  • Qualifies for free U.S. shipping over $35
Compatibility reminder: This is remanufactured, non-OEM ink. Do not purchase it for an HP+ printer that requires Original HP cartridges. Resolve any Instant Ink account restriction before ordering.

Does Your Printer Use a Different HP Ink Family?

If the old cartridge does not say HP 67 or HP 67XL, use the correct product family instead of forcing an HP 67XL cartridge into a similar-looking printer.

Example Printer Correct Ink Family myCartridge Product
HP ENVY Photo 6255 / 7155 / 7855 HP 64 / 64XL Shop HP 64XL
HP ENVY 4520 / OfficeJet 3830 / DeskJet 3630 HP 63 / 63XL Shop HP 63XL
HP ENVY 5540 / OfficeJet 5740 HP 62 / 62XL Shop HP 62XL
HP OfficeJet Pro 8025 / 8035 HP 910 / 910XL Shop HP 910XL
HP OfficeJet Pro 8710 / 8720 / 7740 HP 952 / 952XL Shop HP 952XL

HP 67XL Cartridge Not Recognized FAQ

Why is my HP 67XL cartridge not recognized?

Common causes include the wrong cartridge family or region, protective tape left on the cartridge, incorrect slot placement, loose installation, dirty copper contacts, cartridge damage, HP+, Instant Ink account status, or changed firmware recognition.

How do I reset an HP printer after installing HP 67XL?

Turn the printer off, disconnect the power cord, wait 60 seconds, reconnect the cord directly to a wall outlet, turn the printer on, and wait until it is idle. Then reinstall and test the affected cartridge once.

How do I clean HP 67XL cartridge contacts?

Remove the affected cartridge and gently wipe only the copper contacts with a clean, dry, lint-free cloth. Do not touch the ink nozzles, use alcohol or water, scrape the chip, or clean inside the printer cartridge slot.

Is a “Used” or “Previously Used” cartridge message normal?

It can be normal with remanufactured ink. Read the full printer message. If an OK, Continue, or Proceed option is available and no account restriction is displayed, follow the prompt and print a test page.

Can I print with only the black HP 67XL cartridge?

Many supported two-cartridge HP printers can use Single-Cartridge Mode. Remove the tri-color cartridge and acknowledge the prompt. Printing with black only is grayscale and should be treated as a temporary solution.

Can I print with only the tri-color HP 67XL cartridge?

Many supported two-cartridge HP printers can temporarily print with tri-color only. Colors can print normally, but black may appear lighter than usual.

Will remanufactured HP 67XL ink work in an HP+ printer?

HP states that HP+ printers require Original HP cartridges. Confirm HP+ status before purchasing remanufactured or non-HP ink.

Will regular HP 67XL ink work after canceling Instant Ink?

HP states that after cancellation, Instant Ink subscription cartridges stop working at the end of the billing cycle and should be replaced with regular cartridges. Confirm that cancellation and the final billing cycle are complete.

Why does the printer say incompatible cartridge?

The cartridge number, printer model, country or region, slot, or supply eligibility may be wrong. Compare the old cartridge label, full printer model, and account status before trying another cartridge.

Why is the ink level still low after installing a new cartridge?

Ink-level communication may not update correctly with some remanufactured cartridges. First determine whether the printer is actually blocking printing or only displaying an estimated level. If printing is blocked or output is abnormal, contact the seller.

What should I send myCartridge support?

Send the order number, complete printer model, affected cartridge color, exact error text, cartridge-label photo, printer-screen or HP Smart screenshot, and the troubleshooting steps already tried.

Official-reference basis: This guide follows HP Support troubleshooting principles for compatible cartridge numbers, correct slots, reseating, dry lint-free contact cleaning, a 60-second power reset, HP+ supply requirements, Instant Ink account status, and Single-Cartridge Mode for supported two-cartridge printers. Printer interfaces and exact prompts vary by model and software version.

myCartridge is an independent supplier of compatible and remanufactured printer cartridges. HP, ENVY, ENVY Pro, DeskJet, DeskJet Plus, HP 67, HP 67XL, 3YM57AN, 3YM58AN, Instant Ink, HP+, and related printer or cartridge model names are trademarks or model references of HP Inc. and are used only to describe compatibility. This page and the linked myCartridge product are not manufactured, sponsored, or endorsed by HP Inc.